Removing old paint job from lower? [Archive] - Glock Talk

PDA

View Full Version : Removing old paint job from lower?


Cole125
10-13-2012, 13:25
Here's the deal, buddy of mine has a older well worn Olympic Arms CAR15 with a crappy paint job on it.

He wants me to refinish and rebuild the lower for him, and then build him another upper.

My question is, what is the most time efficient way to remove a crusty old paint job off a lower?

Thanks

iceburg
10-13-2012, 13:29
Just a wild guess, but I believe the judicious use of some sort of abrasive blaster would do it.

Outdoor Hub mobile, the outdoor information engine

M&P15T
10-13-2012, 13:48
I foolishly painted the lower of my AR with Krylon a few years back. I used some gel type paint remover from Lowes to remove it, and it didn't even hurt the phosphate finish on it, looks good as new.

Took some time, but if you are going to re-paint it, removing the old paint may not even be necessary. Just do a good base coat over the old paint. Or remove as much as of the old paint as necessary without going over-board in the cracks and crevices.

ak103k
10-13-2012, 15:31
As long as the paint isnt one of the "permanent" types, something like Gun Scrubber, or even Hoppes, will often take it off without to much trouble. Its mostly what I use when I do strip the paint off. A stiff toothbrush, Q Tips, and in some cases (probably not this one though), steel wool, will make things go quicker, and with better results.

WoodenPlank
10-13-2012, 15:39
Just a wild guess, but I believe the judicious use of some sort of abrasive blaster would do it.

Outdoor Hub mobile, the outdoor information engine

It'll also strip the upper layer of anodizing.

OP, I've had good luck with copious amounts of paint thinner (keep away from plastic bits) on a clean cotton rag and some elbow grease.

samuse
10-13-2012, 16:29
Aircraft remover and/or acetone. And some elbow grease.

Cole125
10-13-2012, 19:29
I'll give paint thinner a try, hopefully it works. It's a 20 year old rifle, with a paint job that could be that old. I have no idea what type of paint it is either.

WayaX
10-13-2012, 20:01
I foolishly painted the lower of my AR with Krylon a few years back. I used some gel type paint remover from Lowes to remove it, and it didn't even hurt the phosphate finish on it, looks good as new.

Took some time, but if you are going to re-paint it, removing the old paint may not even be necessary. Just do a good base coat over the old paint. Or remove as much as of the old paint as necessary without going over-board in the cracks and crevices.

Follow this. Lowes sells an orange gel that I've used to strip paint from an entire rifles. It just takes elbow grease. Do not blast it!

AK_Stick
10-13-2012, 20:04
Go to any local auto parts store, and buy a couple cans of aircraft paint remover, in either the regular paint can, or the spray can, and presto, gun will become un-painted, but not damage the anodizing.

Mayhem like Me
10-13-2012, 22:34
I did this 2 days ago.
Go to home depot get a can of spray Kleen strip.
Get a good pair of rubber gloves goggles and a toothbrush .
spray on thick let sit for 20 minutes hit with high pressure garden hose and scrub with brush it all. Comes off.

Trust me on this it was very easy.

Hour13
10-13-2012, 22:37
Carb Cleaner!


Had a couple beverages, decided I was tired of the tiger-stripes...
http://i306.photobucket.com/albums/nn269/hour13/100_5605-1.jpg

http://i306.photobucket.com/albums/nn269/hour13/100_5609.jpg

http://i306.photobucket.com/albums/nn269/hour13/100_5610.jpg

Then realized the next day I kinda liked the old paintjob...
http://i306.photobucket.com/albums/nn269/hour13/100_5674.jpg

http://i306.photobucket.com/albums/nn269/hour13/100_5690.jpg

LOL.

:faint:

Cole125
10-13-2012, 22:41
:laughabove:

Hour13, your a funny guy! :rofl: Thanks for the tip.

WoodenPlank
10-13-2012, 22:42
Carb Cleaner!


Had a couple beverages, decided I was tired of the tiger-stripes...
LOL.

:faint:

What a marooon....

Hour13
10-13-2012, 22:56
What a maroon....

Lol, most people who talk to me spell it different I think.
:cheers:



:laughabove:

Hour13, your a funny guy! :rofl: Thanks for the tip.

I does what I can brother.

:wavey:

NeverMore1701
10-13-2012, 23:20
I've been thinking about painting my Noveske on and off since I got it a couple of years ago, might actually do it next week. Never tried painting any kind of pattern before, but if it's fairly easy to get off, I'll give it a shot. The carb cleaner doesn't mess up poly parts (PG, stock, HGs)?

smokin762
10-13-2012, 23:21
I went to Home Depot and bought Green Strip Brand paint remover. It's a gel in a squirt bottle. It removes Paint, Epoxy and Varnish. I also used an M16 cleaning brush.

I used it to remove the factory paint on my Ruger 10/22. It stripped it down to the bare surface. It will not harm the anodizing finish. I tried it on a scope mount and it never hurt it.

Don't forget to wear gloves.

Hour13
10-13-2012, 23:38
I've been thinking about painting my Noveske on and off since I got it a couple of years ago, might actually do it next week. Never tried painting any kind of pattern before, but if it's fairly easy to get off, I'll give it a shot. The carb cleaner doesn't mess up poly parts (PG, stock, HGs)?

No, but it does take awhile to get the paint off the plastic stuff. I wouldn't leave it on there, just spray it into your rag, and scrub away.

Cleans up the anodized surfaces like nobody's business though. Wipe with soaked rag, then dry rag. Easy-peezy.
:cool:

FYI, I use plastic/vinyl dye instead of regular paint. It is easier to remove(except from plastic, duh) if you don't like it, and yet it's more durable than paint. It doesn't chip, just gradually wears thin if you're really rough on the gun.

Actually looks pretty cool the more it wears down.

...

But I'm kinda weird like that.

:upeyes:

NeverMore1701
10-13-2012, 23:59
Got a link to this dye? I'll probably just try krylon at first, but I'm open to other methods.

ak103k
10-14-2012, 06:50
Ive always used Testors, and just recently, some Krylon on my guns. Testors Military Flats have been around forever, and come in pretty much any color you need to match a camo pattern.

They will come completely off (with some work) and no damage to the gun underneath. Basic Krylon has too, but I probably wouldnt use the "Fusion" version on plastics.

These were painted about 30 years ago now in the old ASAT pattern using Testors. I stripped the 1100 a couple of years ago and swapped out the stock.

Looked like this then (the Mossberg still does)....

http://im1.shutterfly.com/media/47b7d700b3127ccec27f8d53d8bf00000010O00CYuWbdo5bsQe3nwk/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Now....

http://im1.shutterfly.com/media/47b8d902b3127ccec4fbc32ee1df00000040O00CYuWbdo5bsQe3nwk/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Ive painted and completely removed the paint off my MP5 a number of times over the years, as well as a number of other guns, and never had any troubles. As I said earlier, a can of Gun Scrubber, and or some Hoppes, was all I ever used. The toothbrush is pretty much a necessity with "grainy" surfaces, like park, some anodized aluminum, and plastics. 0000 steel wool is a big help on smooth steel.

Hour13
10-14-2012, 18:59
Got a link to this dye? I'll probably just try krylon at first, but I'm open to other methods.

It's krylon also, "Krylon Fusion". You can get it at WalMart with all the other rattle-cans.

:supergrin: