View Full Version : Backstrap Channel Insert for G26
Backstrap Channel Insert for G26. What are my options?
I have a Deep6Comp/Glockmeister in my G17 and G19. I really like this plug. I was wondering what are the "slight receiver modifications" needed to fit this plug to a G26.
Any other "no modifications needed" plug I should look for? A low profile is preferred.
Any help will be appreciated :)
They have to drill a small hole in the backstrap to get it to fit....like the one you have in your 17 and 19.
Originally posted by 360
They have to drill a small hole in the backstrap to get it to fit....like the one you have in your 17 and 19.
"They" means you have to mail the frame to Glockmeister or its really a do it yourself project? Any other modification besides the lanyard hole?
douglasd
08-09-2007, 22:07
They make one specifically for the subcompacts...it doesn't have the little "bump" thingy on it to go in the hole. You just need to glue it in with some silicone caulking/sealer to make it stay.
Check here:
http://www.topglock.com/catalog/extras.htm#plugs
#42313 Jentra Plug for models 26, 27, 28, 33 is what you want.
To make my plug stay in my 26, I just wrapped it in a bit of electrical tape and press fitted it, I dont like the idea of drilling a hole in my gun or putting glue in there when I dont need to.
Originally posted by SFIPSC
To make my plug stay in my 26, I just wrapped it in a bit of electrical tape and press fitted it, I dont like the idea of drilling a hole in my gun or putting glue in there when I dont need to.
+1 I dont like to drill or glue my frame either. The electrical tape idea sounds good to me. What plug you used?
kiwibird1
08-10-2007, 07:25
What is the plug for? Does it serve a purpose?
Originally posted by kiwibird1
What is the plug for? Does it serve a purpose?
I think it is only used to keep dirt out. I have one on my 19 but not my 26. I felt that it was not worth it, IMHO.
Originally posted by kiwibird1
What is the plug for? Does it serve a purpose?
Both my G26 and G34 have them. They serve two missions...
Keep out lint, and quicker mag changes. ;)
Not bad for $10.
Originally posted by kiwibird1
What is the plug for? Does it serve a purpose?
I just want to keep my Glocks internals as clean as possible. Although many advocate for faster mag changes, I practice, practice and practice (did I said practice?) mag changes and I've never noted any speed improvement.
Also I dont like to have a hollow unfilled space in the backstrap, just for the looks ;)
Originally posted by Cochese
Both my G26 and G34 have them. They serve two missions...
Keep out lint, and quicker mag changes. ;)
Not bad for $10.
Which one you use in your G26?
I was all set to put a plug in the grips of my Glocks until I talked with a few Glock armorers. All of them stated that the plugs do keep some stuff out, but they also trap some stuff in when you shoot. After hearing that I decided to leave my Glocks "plugless."
Originally posted by TacDoc
Which one you use in your G26?
I've had both. My used G26 had an outie.
My newer LE one has the Jentra flush. :)
douglasd
08-10-2007, 20:52
Originally posted by klt1986
I talked with a few Glock armorers. All of them stated that the plugs do keep some stuff out, but they also trap some stuff in when you shoot.
That's just an excuse to not spend the money on them. There's nothing it could "trap" that would hurt anything. It's going to keep out a LOT more than it could ever trap.
As for me, I just think the gun looks a lot better with it, and it also strengthens the grip slightly. And it does make it easier to insert a mag quickly because of the beveled edge.
douglasd
08-10-2007, 20:55
PS...it doesn't take much to be a GLOCK armorer. If you can detail strip the gun, and replace the parts, you are an armorer. It doesn't mean they know anything more than you know, if you've had any experience detail stripping or repairing your own GLOCKs.
That is, if you're the least bit mechanically inclined.
Originally posted by douglasd
PS...it doesn't take much to be a GLOCK armorer. If you can detail strip the gun, and replace the parts, you are an armorer. It doesn't mean they know anything more than you know, if you've had any experience detail stripping or repairing your own GLOCKs.
That is, if you're the least bit mechanically inclined.
Well since I can do that I guess I am an armorer!;) I feel like if the grip plugs were a necessity the channel would be plugged from the factory. IMO the plugs serve more for looks than for actual function. If the weapon is properly cleaned and lubed there should be no need for a grip plug.
I may try one out some day and compare the cleanliness of plugged Glocks to non plugged Glocks.
Originally posted by douglasd
PS...it doesn't take much to be a GLOCK armorer. If you can detail strip the gun, and replace the parts, you are an armorer. It doesn't mean they know anything more than you know, if you've had any experience detail stripping or repairing your own GLOCKs.
That is, if you're the least bit mechanically inclined.
That means I'm an AR (4 builds and counting), AK (2 builds), Remington 870 (1 build) and Glock (17, 19 and 26) armorer!!! Probably a 1911 armorer aswell as I've completely stripped and "modified" my Wilson Combat.
Now I feel great!!! :thumbsup:
douglasd
08-11-2007, 11:58
Ok, you guys...you know what I meant.
I just meant that an armorer's course is usually just one day, and basically consists of a bit of theory of operation, detail stripping and replacing parts, and some troubleshooting of why the gun does this or that.
If you have experience with GLOCKs, and are good with tools, you can do all of the above and know just as much as an "Armorer", depending on your and his experience.
The only thing missing is the Certificate that makes it official. GLOCKs are the easiest handgun to work on, IMO.
douglasd
08-11-2007, 12:03
Originally posted by klt1986
IMO the plugs serve more for looks than for actual function.
You're right. As I said, I like them for their looks more than anything else...to me it just looks like something is missing without it.
Most LEO's I've seen do not use them, at least in my area. Of course, it's probably just that they are not issued them, and don't want to buy them themselves.
However, it does keep a bit of dust out of the back channel and adds a bit of strength to the plastic at the back of the grip. But they are truly not "necessary".
vBulletin® v3.7.3, Copyright ©2000-2008, Jelsoft Enterprises Ltd.