Anyone have experience with G26 +2 mag extensions from Pearce

[Range Guy]

I'm debating on buying them. Does anyone have these? If so is there any issues?

[gary newport]

Yes. No.

[Range Guy]

Thanks

[p3v5]

I have them and they are fine. I have had no issues with them whatsoever.
The hardest thing to do is get the floor plate off of the magazine to install the extension.

[ab4ka]

I don't like them because they pinch my finger. I prefer the Glock or Scherer extensions which are flat on the front.

[glock2740]

I have a couple and they work just fine.

[garageman]

I don't like them because they pinch my finger. I prefer the Glock or Scherer extensions which are flat on the front.

Same here. They worked just fine with no malfunctions...just pinched my finger quite a bit. I replaced them with the GAP floorplate and absolutely love them.

[AMG ETR]

Can anyone confirm which one I have?? I have the PG-2733.... I was told when I got it, that it was +0, but I have seen a slimmer one which leads me to believe this one is the +2 and I haven't even known it!!
Thanks,
Evan

[garageman]

Can anyone confirm which one I have?? I have the PG-2733.... I was told when I got it, that it was +0, but I have seen a slimmer one which leads me to believe this one is the +2 and I haven't even known it!!
Thanks,
Evan

I see on the package that it is the model PG-39 and it says "+1 for model 39, +2 for model 27/33, and +3 for model 26". However, I never forced 3 on the G26 magazine - always used it as a +2.

[stratmeister]

Is there an option of using a standard Glock mag for increased capacity? Like in my G30 I use a G21 mag...

[Companion Cube]

I have the PG-39 and the PG-2733. As far as feel is concerned, I much prefer the 2733.

[davebloomer]

I have one and plan on buying another for the other mag. no issues at all. installation is pretty simple.. get a small screwdriver push it in the hole then squeeze the sides and pry back with the screwdriver. takes 2 seconds. Also these don't effect printing issues for me.


EDIT: I need to read my post before posting a lot more often

[waltosha]

i got two of the pg39 that says you can add 3rds for the 26 i can only get two to fit other than that no problems they work fine

[AMG ETR]

So my 2733 really is a +2?? Damn, been carrying 10, would love to have 12 if thats true...
Evan

[D-GLOCK17]

Can anyone confirm which one I have?? I have the PG-2733.... I was told when I got it, that it was +0, but I have seen a slimmer one which leads me to believe this one is the +2 and I haven't even known it!!
Thanks,
Evan

When I bought one the other day, the guy had a small box with several. He was looking through them and I grabbed the #2733. He replied, " I am trying to find you a +2". I said I take that one because I've heard good things about the +0 also. When I got home, I noticed on the back of the pack that it actually is adds 2 (for the G26). I paid $10 even for it.

I have one and plan on buying another for
the other mag. no issues at all. installation is pretty simple.. get a small screwdriver push it in the hole then squeeze the sides and pry back with the screwdriver. takes 2 seconds. Also these don't effect printing issues for me.


EDIT: I need to read my post before posting a lot more often

It took me probably 45 mins or so to get the stock baseplate off of my G26 mags.

So my 2733 really is a +2?? Damn, been carrying 10, would love to have 12 if thats true...
Evan

Ha Ha. Just as I posted above, the guy and the store thought he was selling me a +0 ext. and I realized it was a +2. I put 11 rounds in the mag once. I normally keep 10 in it though.

[AMG ETR]

Ahh very cool, thanks for confirming! I actually like the +0 "curved" one better for looks, so I may get one for my other mag, but I have gotten comfortable carrying this 2733 so thats good to know I can carry 12 in there! Anyone know the model number for the +0 "curved" plate??
Evan

[MCPO]

For my G26, here are the 3 Brownells show:
PG-26 +0
PG-2733 +2
PG-39 +3

They also sell the ones labeled as XL (example = PG-39 XL) which is a 1/4" longer but sill a +3.

I have (2) of the PG-26 and (2) of the PG-39 XL that will soon go in the Sale section as they have been replaced with GAP extensions. The PG-26 pinched my finger and the PG-39 XL is a nice fit and no pinch problem, but shows a sharp print when in my holster.

[BustedFlush]

It took me probably 45 mins or so to get the stock baseplate off of my G26 mags.
This is the link to the Gunsmithing Forum:

http://glocktalk.com/forums/forumdisplay.php?f=23

At the very top is a stickied thread - how to disassemble a Glock mag.

Read it, find the link to the video made by GT member Randy Smith.

After a little practice, you should be able to get a mag floorplate off in 10 seconds.