Glock Talk

Glock Talk (http://glocktalk.com/forums/index.php)
-   Black Rifle Forum (http://glocktalk.com/forums/forumdisplay.php?f=93)
-   -   sighting in optic (http://glocktalk.com/forums/showthread.php?t=1172293)

RUSH2112 01-18-2010 09:34

sighting in optic
 
New BUIS and red dot. Can I just zero my irons, and then while looking down the sights, dial the dot just over the front post and I'm good? (Or goodish?)

MCKNBRD 01-18-2010 11:57

That will get you pretty close; I'd still check it before trusting my life to it, or taking it hunting and risking wounding an animal.

Byrdman

RUSH2112 01-18-2010 12:21

I'll definately make sure it's right by the time I'm done. I figured doing it this way will use up fewer rounds.

gunsnhoses 01-18-2010 14:31

That's what I did and I was pretty much dead on.

crazypilot 01-18-2010 14:38

Quote:

Originally Posted by RUSH2112 (Post 14568671)
New BUIS and red dot. Can I just zero my irons, and then while looking down the sights, dial the dot just over the front post and I'm good? (Or goodish?)

Yes. That's the way to do it. Then fine tune the red dot.

lawman800 01-19-2010 02:29

Get a laser boresighter for $30 and do it right. How did you plan on sighting your irons without shooting? If you're going to be shooting, might as well sight in your red dot correctly.

RUSH2112 01-19-2010 05:49

Quote:

How did you plan on sighting your irons without shooting?
:rofl: I never said that.

My brother inlaw has a laser boresight, I'll be using that to start with, but all that does is get the scope aligned with the bore axis. I'm talking about after that's done.

RWBlue 01-19-2010 10:36

Quote:

Originally Posted by RUSH2112 (Post 14568671)
New BUIS and red dot. Can I just zero my irons, and then while looking down the sights, dial the dot just over the front post and I'm good? (Or goodish?)

Assumine that you mounts allign properly (not putting the iron low in the red dot window), your method described above is the correct method.

And assuing your irons are correct there should be no need for additional adjustments.

internal 01-19-2010 11:47

If that's good enough for you then so be it.

But why would you go through the trouble driving to your shooting spot and sighting your irons in and then just "eyeball" the zero on your red dot that you purchase with your hard earned money.

That just seems lazy to me.

CrazyFeet 01-19-2010 12:14

once the irons are good doing that will get you very close and you wont need to take too many shots to get it near perfect.

RWBlue 01-19-2010 13:56

Quote:

Originally Posted by internal (Post 14576878)
If that's good enough for you then so be it.

But why would you go through the trouble driving to your shooting spot and sighting your irons in and then just "eyeball" the zero on your red dot that you purchase with your hard earned money.

That just seems lazy to me.

I have done this several times. I know if I have two fixed points, I can adjust a third point inbetween those points. I have never considered myself extraordinary in this ability.

Please explain why this would be an issue. It appears to be simple engineering.


All times are GMT -6. The time now is 12:20.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2013, Glock Talk, All Rights Reserved.