Glock Talk

Glock Talk (http://glocktalk.com/forums/index.php)
-   Reloading (http://glocktalk.com/forums/forumdisplay.php?f=26)
-   -   Do you clean after you tumble? (http://glocktalk.com/forums/showthread.php?t=1453843)

TH237 11-19-2012 00:34

Do you clean after you tumble?
 
I normally use untreated walnut hull, however... The Lyman tufnut treated with polishing compound was all they had. I used it as normal but when I checked the cases I saw a lot of the compound on the cases. I know I can wipe it off the outside but what about the inside? Do any of you wash the cases with soap and water to remove it? Perhaps there is a better way. If so please share.

Thanks.

JBnTX 11-19-2012 00:41

I just put them in a towel and work them for a few minutes.
Gets most of the leftover stuff off.

You shouldn't be getting anything inside the cases?

http://www.lymanproducts.com/lyman/f...mblers_faq.php

..

TH237 11-19-2012 01:21

There is definitely red residue inside the cases. I mean the cases are obviously open and immersed in the media.

twag4 11-19-2012 05:53

I have some of thst media as well. It only leaves the residue on the first batch or two. After that its ok. I just load them. Never had a problem.

alwaysshootin 11-19-2012 07:54

Used some of the treated years ago, never again! Plain crushed walnut, from here on out, for me, thanks!

Kentguy 11-19-2012 08:17

TH237... "Do any of you wash the cases with soap and water to remove it? Perhaps there is a better way. If so please share."

Like "Alwaysshootin", I also tried that product years ago and like him I agree... Never again.

My process is a bit more cumbersome than most. Bottom line reloading is a Hobby for me, not a job, so I don't mind putting in the time to get the results that I want.

Short & sweet version, after you have de-primed your casings;

1st. put them in bucket with warm water & "Birchwood Casey Brass Cartridge Case Cleaner" (just follow the directions).
2nd. next spread them out on a towel, than I take a "Q-Tip" and swab out the primer pocket and the interior of the case itself.
3rd. Dump em in the tumbler (with corn media mix) & and squirt of "Nu-Finish" car/metal polish... 3 hrs later they come out like a brand new shinny penny both inside & out.

Makes inspection extremely through. Like I said my process in not for everyone but this is the way I conduct it for my standards.

Good luck & have fun

W.E.G. 11-19-2012 08:38

I use plain ground walnut shells.

Never any polish, solvent or goo in the mix.

After cases come out of tumbler, they go on a towel on the floor for the one or two that still have walnut hiding in them to dump their load.

Cases are then ready for resizing.

Boxerglocker 11-19-2012 08:54

I run 2 tumblers at a time, buy 40# bags of corncob. Tumble 3-4 hours with Nu-Finish cut with a little paint thinner and toss in a cut up dryer sheet.
I keep a little walnut on standby in case I come upon a lot of really dirty brass, I never treat it with anything though. Tumble for 2 hours and toss it in the corncob to final clean.
I like really shiny brass, makes it easier to find cracks particularly on rifle case necks.
I'm hoping to get a wet SS media tumbler for Christmas to process my Lapua brass for my bolt gun.

Kwesi 11-19-2012 09:03

Quote:

Originally Posted by Boxerglocker (Post 19647385)
I run 2 tumblers at a time, buy 40# bags of corncob. Tumble 3-4 hours with Nu-Finish cut with a little paint thinner and toss in a cut up dryer sheet.
.

I only load pistol and do not deprive prior to tumbling. Nu-Finish works great and acts as a lubricant. I find 2-3 hours in the tumbler is all it takes. I believe boxer is referring to used dryer sheets.

stevelyn 11-20-2012 01:03

Quote:

Originally Posted by TH237 (Post 19646737)
I normally use untreated walnut hull, however... The Lyman tufnut treated with polishing compound was all they had. I used it as normal but when I checked the cases I saw a lot of the compound on the cases. I know I can wipe it off the outside but what about the inside? Do any of you wash the cases with soap and water to remove it? Perhaps there is a better way. If so please share.

Thanks.


I use the Lyman TuffNut. I only use it if the cases are extremely dirty or stained and on all range pick-up brass the first time.

I toss them in corn cob media afterwards with a little Frankford Arsenal case polish and it cleans the jewelers rouge out of the cases.

SigFTW 11-20-2012 07:50

I use corncob also, and a dryer sheet to keep it clean. Works great for what I need.

dkf 11-20-2012 09:30

I bought some of that Red Lyman tuffnut stuff due to lack of options when I bought the tumbler. I have used it many times and it still leaves the red from rouge all over the cases. To remove it tumble in untreated media. I just keep the red stuff for really dirty brass since I have it. It is really not worth the trouble.

Colorado4Wheel 11-20-2012 10:31

If I had some of the red stuff I would reduce it with some regular. Sounds like it just has way to much polishing media in it.

ejs54 11-21-2012 00:44

I've been using walnut sold as pet litter. Recently I have been accumulating a lot of brass in different conditions and adding Flitz media polisher into the mix. This works well for cleaning and polishing but it does leave an annoying dust behind.

Right now I'm recycling the media well over 10 times and running all the bulk brass with it. Eventually will dump it out and use plain walnuts without any chemicals on my spent casings which don't need much cleaning.

Zombie Steve 11-21-2012 09:38

The Lyman Tufnut really does a great job at cleaning up the cases, but you've already discovered the down side - all the rouge everywhere.

I just mix it about 5:1 corncob:walnut and make sure to put in some cut up dryer sheets and it minimizes the dust / rouge everywhere.

racer11 11-21-2012 16:52

I soak my cases in Purple Power for about a hour and rinse and dry. Then I tumble in corn cob media and then I resize and deprime and process.

EKUJustice 11-22-2012 09:40

I use corncob media from the walmart pet section and a capfull or so of nufinish from automotive every few cycles. I put a dryer sheet or 2 in every cycle. the brass comes out shining and no residue

EL_NinO619 11-22-2012 11:49

I second Boxer, I run two tumblers, lyman 1200 and the huge one from Harbor Freight. I buy cheap corn cop media use a dap of new finish and cheap dryer sheets, They come out looking brand new. I do however have the brand new Hornady ultrasonic cleaner coming, the one you can fit your whole AR upper in, can't wait to see how that works for both rifle and precision rifle brass.

http://www.hornady.com/assets/images...h-barrel-2.jpg

MtnBiker 11-23-2012 19:25

I've never had residue stay on the brass like that. After tumbling, I just put the brass in a mesh bag and shake it up so any remaining walnut shell media falls out.

MannyA 11-23-2012 19:49

Well hell ya
My back gets all dusty!


Crushed walnut and nu finish and call it good


All times are GMT -6. The time now is 14:32.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2013, Glock Talk, All Rights Reserved.