GlockTalk.com
Home Forums Classifieds Blogs Today's Posts Search Social Groups



  
SIGN-UP
Notices

Glock Talk
Welcome To The Glock Talk Forums.

 
  
Reply
 
Thread Tools Display Modes
Old 01-25-2013, 18:05   #1
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
4 FTFs with Underwood Ammo

Hey guys, got a problem here. In the last two boxes of Underwood 180gr TMJ, I've had four instances where the primer was struck, but my Glock 20 did not fire. I wanted to post up here to see what could be some causes. I'm loath to immediately blame Underwood, however I have never had this problem with Double Tap and shot a couple boxes in the last 3-4 months flawlessly. At the same time, Underwood Ammo has given me problems

Pics of the strikes

The 10 Ring

The 10 Ring


The far left is a round that fired properly. The middle and far right are both FTFs. They are sitting as they did in the chamber. I drew a line with a marker at the top and verified before firing. Took me about a dozen rounds, but I got two. This has happened at least twice before, but single rounds.

Notice how both of the FTFs seem to be to the right, instead of center? What does that mean? Anything?

What do I need to check on my gun?

Last edited by Slateman; 01-25-2013 at 18:06..
Slateman is offline   Reply With Quote
Old 01-25-2013, 18:40   #2
AA_Khost
Member
 
AA_Khost's Avatar
 
Join Date: Apr 2012
Posts: 1,188
http://glocktalk.com/forums/showthread.php?t=1456690
__________________
“You've never lived until you've almost died. For those who have fought for it, life has a flavor the protected shall never know.”

Si vis pacem, para bellum
AA_Khost is offline   Reply With Quote
Old 01-25-2013, 18:47   #3
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
A light, off center striker hit is a round that wasn't fully chambered and locked into battery. Could be any number of reasons, including a dirty chamber, expanded case mouth (not crimped properly), oversize bullet, extended bullet bearing surface, or a bullet ogive that starts too slowly forward of the case mouth. This is very rare with almost any round in the OEM Glock barrel, but isn't uncommon with some aftermarket barrels.

With the barrel removed from your pistol, drop the rounds into the chamber. They should fall all the way into the chamber, flush or slightly recessed below the hood, and rotate freely. If not, you need to find out where they are interfering. I color the case mouth (about 1/4" back) and bullet with a marker and force them in by hand. The ink will be wiped from the area of the interference.

The rounds in your pic were not in the chamber like that. They are rotated from their firing position. If you marked them before chambering, it's likely, and common, they rotated while chambering. They won't normally stay in the same orientation going from the mag to the chamber, for a couple reasons. The primer strikes should be either centered like the "fired" round, or high-center. The rectangular dent on the primer of the fired round should be vertical, and can't be any other way. A round going into or out of the chamber can only be presented to the vertical center line of the striker, as the breach is a channel, the round slides up while moving forward into the barrel chamber, and any friction at the case head or rim can cause rotation. It is pulled straight out by the extractor with no rotation.
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-26-2013, 18:41   #4
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
This is how the round sits in the chamber:

The 10 Ring

The 10 Ring


Also, is this normal for the firing pin assembly:
The 10 Ring

Is the rear supposed to be slightly off center like that?
Slateman is offline   Reply With Quote
Old 01-26-2013, 19:10   #5
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
Your striker assy appears normal. The "rear" part is only a plastic sleeve. When installed in the striker channel, the sleeve will be straight, or as straight as it needs to be. If it isn't broken, cracked or deformed, it'll work as necessary. When removed from the slide, the spring tension will cause it to cant slightly toward the striker lug. Your fired round shows a completely normal (ideal, actually) strike. In other words, completely normal. The problem happened with the rounds that did not fire that have the offset strikes. Something prevented the barrel from going into full battery lockup.

Are the rounds (pictured) in the chamber completely engaged? In other words, is the case head below the level of the hood? You can use a straight edge to confirm. Do the rounds go in and fall out easily? Can the round be rotated in the chamber easily, and still fall out freely? Carefully inspecting the case heads, is there any abnormality, such as any part that may be a larger diameter, thicker, or have a gouge (like an extractor mark)?

Also check the forward end of the chamber. Use a scribe or toothpick and scrape the ledge where the case mouth engages. Any fouling buildup (copper, powder residue, etc.) there can prevent full chambering with cases that are near full length.
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-26-2013, 19:38   #6
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
They are completely level. I can rotate them freely and it falls out easily as well.

I don't see any marks on the round that are abnormal from the unfired rounds.

I've cleaned out the firing pin channel thoroughly. To be honest, it's probably been 8-10k rounds since it was last done. Assuming the previous owner did it.
Slateman is offline   Reply With Quote
Old 01-26-2013, 20:36   #7
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
I don't think your problem is the striker. If you had only light strikes, perhaps. But, the strikes are off center, meaning the cartridge wasn't presented in full lockup, the primer wasn't centered in front of the firing pin.

At the very least, with that many rounds through the pistol, the RSA (recoil spring assy) should have been replaced several times by now, and may be due again. While a weak spring can cause FTF/F's, the combination of an otherwise tight fitting round (such as many Underwood rounds) and a weak spring is a recipe for FTF's. Glock recommends about 5K rounds between RSA replacement. In my experience, about 3K is more realistic, especially if the pistol is used for any form of defense, on duty, concealed carry, or home. They are cheap and readily available, so no reason to not replace them regularly.
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-26-2013, 20:41   #8
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
Okay. I'll check it tomorrow. If I'm still getting those issues, I'll go with a new recoil spring. I ordered a 20lb with SS guide rod from Glockmeister. Been meaning to get it anyway.
Slateman is offline   Reply With Quote
Old 01-26-2013, 20:46   #9
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
It may be as simple as that. I've found heavier rounds, such as Underwood, do better with a heavier spring. Others disagree. YMMV.
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-26-2013, 20:48   #10
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
What is the "stock" spring weight?
Slateman is offline   Reply With Quote
Old 01-26-2013, 20:59   #11
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
17 pounds.
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-27-2013, 05:48   #12
4949shooter
Senior Member
 
4949shooter's Avatar
 
Join Date: Aug 2006
Location: New Jersey Republik
Posts: 13,059


I had this issue with an early Gen 2 Glock 23. Every once in a while I would get a light strike on the primer and fail to fire. I had the RSA replaced with a fresh one and fired 900 rounds without cleaning the gun (it was a test) and had no issue.

Edit: I will be firing 200 rounds of the Underwood 180 grain fmj today as a matter of fact. I will let you know if there are any problems, but I doubt it was the ammo.
__________________
"...the men under your command deserve your leadership."-OXCOPS

Last edited by 4949shooter; 01-27-2013 at 05:49..
4949shooter is offline   Reply With Quote
Old 01-27-2013, 11:45   #13
G29SFWTF
Senior Member
 
Join Date: Aug 2012
Posts: 206
G29SFWTF is offline   Reply With Quote
Old 01-27-2013, 11:56   #14
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
Went to the range, fired ~75 rounds no problem. Not exactly definitive, but a good sign.

They did not have a RSA or firing striker spring in stock. Anyone know a place that has them in stock? I have an order in to Glockmeister so I may call tomorrow and see if I can get a stock RSA added in.
Slateman is offline   Reply With Quote
Old 01-27-2013, 12:08   #15
dm1906
Retired SO
 
dm1906's Avatar
 
Join Date: Sep 2010
Location: PRK (Kalifornia)
Posts: 428
Numrich has them in stock. Shipping from them has always been fast to me. www.gunpartscorp.com #805620
__________________
Life is tough. It's tougher if you're stupid. -- The Duke
dm1906 is offline   Reply With Quote
Old 01-27-2013, 16:35   #16
RYT 2BER
Senior Member
 
RYT 2BER's Avatar
 
Join Date: Apr 2011
Location: The Gunshine State
Posts: 2,518
Tagged
__________________
Unfortunately, with all the advances in medical science, there still just isnt any cure for "stupid".
RYT 2BER is offline   Reply With Quote
Old 02-04-2013, 17:12   #17
qfkeon
Member
 
qfkeon's Avatar
 
Join Date: May 2003
Location: Michigan
Posts: 50
My new G20 Gen3 was doing this and I contacted Glock. I was told by Glock this is sometimes an issue and they asked me to send them the gun. I haven't had a problem since I got it back.
qfkeon is offline   Reply With Quote
Old 02-04-2013, 21:00   #18
ModGlock17
Senior Member
 
ModGlock17's Avatar
 
Join Date: Dec 2010
Location: Lalaland USA
Posts: 2,626
Slightly off topic. I run my firing pin assembly a little wet with Frog lube. Yours look bone dry. I also polished my firing pin shaft to a chrome shine. They are easier to clean when they are slicky.. FWIW
ModGlock17 is offline   Reply With Quote
Old 02-05-2013, 07:16   #19
Slateman
Senior Member
 
Join Date: Aug 2005
Posts: 163
Quote:
Originally Posted by ModGlock17 View Post
Slightly off topic. I run my firing pin assembly a little wet with Frog lube. Yours look bone dry. I also polished my firing pin shaft to a chrome shine. They are easier to clean when they are slicky.. FWIW
It's bone dry because I had wiped it off and started the cleaning process. However, I didn't exactly lube it up a lot before re-inserting it. I figure lube will naturally work it's way in there, but I'm usually quite light with the lube.

Update:
Got the parts installed in Glock. Figured I'd burn through some ammo to test it. Gone through about 3 boxes with no issues, so thanks for the help. Since I wanted to take pictures, here's some of my work at the range.

Target is 8.5" wide, 11.5" tall. Paper is 11x17
Load: 180gr Underwood FMJ
Pistol: Stock Glock 20C

First pic is rapid pairs at 7 & 12 yards and single shot at 15 yards:
The 10 Ring


Then I got bored and wanted to see what it was like to shoot pistol with a bench. This is at 25 yards with a bench/chair:
The 10 Ring

Had three rounds left, and didn't like sitting while shooting a pistol. Single shots, standing at 50 yards:
The 10 Ring

Honestly, at 50 yards with a 4 inch barrel, I was just looking to hit paper.

In other news, Glockmeister has yet to return an email or pick up the phone.
Slateman is offline   Reply With Quote
Old 02-05-2013, 07:45   #20
GRT45
Transform & Win
 
GRT45's Avatar
 
Join Date: Jun 2010
Location: Texas
Posts: 2,914
Quote:
Originally Posted by Slateman View Post
It's bone dry because I had wiped it off and started the cleaning process. However, I didn't exactly lube it up a lot before re-inserting it. I figure lube will naturally work it's way in there, but I'm usually quite light with the lube.
You are quite correct to leave the firing pin and firing pin channel dry according to Glock's recommendation. On page 79 of the Glock Armorer's Manual, ©GLOCK 2009, there is a big Caution Box with these words in bold print:
"Never leave any solvent or put any lubricant inside the firing pin channel or magazine tube. Along with the breech face and barrel chamber, these areas should be wiped dry before reassembly or use. Leaving solvent or lubricant in any of these areas may cause contamination of primers or powder and possible failure to fire."
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.
: Strictly monogamous, I have one Glock and one woman.
GLOCK Certified Armorer,
To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.
Member,
To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.
Endowment Member, Eagle Scout

Last edited by GRT45; 02-05-2013 at 07:50..
GRT45 is offline   Reply With Quote

 
  
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




All times are GMT -6. The time now is 19:47.




Homepage
FAQ
Forums
Calendar
Advertise
Gallery
GT Wiki
GT Blogs
Social Groups
Classifieds


Users Currently Online: 1,332
420 Members
912 Guests

Most users ever online: 2,672
Aug 11, 2014 at 2:31