Detail Stripping the Kahr's Upper

Michigun · 11-12-2004, 07:23

How To Detail Strip the Kahr's Upper!

CHECK OUT MY 2nd TO LAST POST IN THIS THREAD FOR THE PDF ATTACHMENT!

Cagey · 12-19-2004, 07:35

Thanks Michigun! I've printed it out and saved it.

Michigun · 12-22-2004, 05:17

Quote:

Originally posted by Cagey
Thanks Michigun! I've printed it out and saved it.

Glad you like it! ^c

(WIG19 gets the credit for getting all my info into that nice downloadable PDF however!

)

chance3290 · 02-15-2005, 13:17

I had been wanting to learn how to do this. I was on the range awhile ago, when I had a bad round that(coupled with the unsupported chamber) sent a couple of part flying. As luck would have it, for once all the parts were quickly found and I had to learn how to put it back together.
Now I'm glad I've got this because I figured if I wanted to take it apart again, I'd have to wait for the parts to blow off again.

Thanks

jam_ppp · 03-28-2005, 11:24

This is my first post here and just wanted to say thanks for this document. Have had my MK9 for about 5 years now and for the first time stripped the slide. Couldn't have done it without these instructions.
FWIW, the slide wasn't all that dirty inside. The one spot there was alot of gunk was under the striker block and in the spring. Didn't seem to affect function but it there was alot of "sludge" in there....

Michigun · 04-20-2005, 10:34

Sorry guys, this thread hasn't been popping up for me...

Anyways, thanks for the feed-back & the good words, I'm VERY glad to see that it’s helped! ^c

recondoc · 05-24-2005, 09:16

Michigun,
Where did it go? Can it be retrieved somewhere else?
Thanks,
Doc

Michigun · 06-01-2005, 11:22

Quote:

Originally posted by recondoc
Michigun,
Where did it go? Can it be retrieved somewhere else?
Thanks,
Doc

Sorry it took me so long... she's all fixed up now! ^c

Michigun · 06-03-2005, 11:57

.

.

Glock4Life · 08-24-2005, 11:07

What a truly nice job!! Excellent work that clearly took some time to get to that level of quality. A+++++++

;Y

BackDraft · 10-31-2005, 20:24

Quote:

Originally posted by Michigun
.

.

Michigun · 11-01-2005, 05:29

Thanks for getting it back up BackDraft! ^c

(I did just fix the main one again.)

BackDraft · 11-01-2005, 10:32

Quote:

Originally posted by Michigun
Thanks for getting it back up BackDraft! ^c

(I did just fix the main one again.)

No Problem thats what I'm here for. Between us we have to hook up and work on the lower end. I do mine about once a year but this year its a respring job.

Michigun · 11-01-2005, 12:40

Quote:

Originally posted by BackDraft
Between us we have to hook up and work on the lower end.

Hey, sounds good! ^c

plumbum2 · 01-01-2006, 19:45

hi michigun. found something out tonight about detail stripping the kahr upper that makes it a little bit easier.

on the first step. (pulling the striker spring, and retaing rod.)

instead of using a flat head screw driver. use an old pair of tweezers.just grab a "coil" of the spring. you can lay the slide on a flat surface. and with one hand use the tweezers and with the other hand stick the side stop in thier to hold it down while you prepare for step 2. the slide basically stays still because of the way the pressure is applied by the tweezers instead of a screw driver.....

hope this helps anyone..

Michigun · 01-03-2006, 05:17

Quote:

Originally posted by plumbum2
hi michigun. found something out tonight about detail stripping the kahr upper that makes it a little bit easier.

on the first step. (pulling the striker spring, and retaing rod.)

instead of using a flat head screw driver. use an old pair of tweezers.just grab a "coil" of the spring. you can lay the slide on a flat surface. and with one hand use the tweezers and with the other hand stick the side stop in thier to hold it down while you prepare for step 2. the slide basically stays still because of the way the pressure is applied by the tweezers instead of a screw driver.....

hope this helps anyone..

Thanks, I'll have to give that a try! ^c

YukonGlocker · 01-10-2006, 03:25

Thanks for the pdf. I stripped the upper of my pm9 tonight and this took all the guessing out. Thanks!!!

Michigun · 01-10-2006, 05:40

Quote:

Originally posted by YukonGlocker
Thanks for the pdf. I stripped the upper of my pm9 tonight and this took all the guessing out. Thanks!!!

Great to hear, thanks for the feedback sir!

silky · 02-02-2006, 21:52

I see the lube diagram, but no detail strip .pdf file to download.
??

Michigun · 02-03-2006, 05:25

Quote:

Originally posted by silky
I see the lube diagram, but no detail strip .pdf file to download.
??

Thanks for the heads up silky... the .pdf attachment must have been dropped again... all fixed! ^c

chief_017 · 02-21-2006, 12:44

i cant open the detail strip pdf. is it just my computer or does the link not work? thanks

Michigun · 02-24-2006, 15:55

Quote:

Originally posted by chief_017
i cant open the detail strip pdf. is it just my computer or does the link not work? thanks

Does your computer have .pdf software? (I ask because the link is still working for me.)

chief_017 · 02-28-2006, 08:36

it finally worked, my computer is just a piece of garbage. thanks.

ArmedChaos · 06-10-2006, 09:41

Just a heads up, I do not believe that the link is active anymore...Justin

Michigun · 06-14-2006, 16:25

Thanks for letting me know ArmedChaos!

Now if someone can just help me out by re-posting the pdf file we'll be back in business! (I can't seem to find my copy on my CPU right now...

)