Home Forums Classifieds Blogs Today's Posts Search Social Groups



  
SIGN-UP
Notices

Glock Talk
Welcome To The Glock Talk Forums.

 
  
Reply
 
Thread Tools Display Modes
Old 09-12-2012, 16:08   #1
racking on
Registered User
 
Join Date: Jul 2012
Posts: 1
Crimping ?

Do you have to crimp handgun reloades for best of grouping on paper at 15-30yds using 9mm G19, also has anyone heard of the consistent crimper at [URL="http://www.precisionaccuracycompany.com"]www.precisionaccuracycompany.com[/URL]? If we do have to crimp will this crimper using lee factory crimp die be worth buying?
racking on is offline   Reply With Quote
Old 09-13-2012, 12:07   #2
Zombie Steve
Decap Pin Killa
 
Zombie Steve's Avatar
 
Join Date: May 2007
Location: Old Colorado City
Posts: 19,935
Generally, you'll have to taper crimp to get it to function in a semi-auto, but don't think of it as crimping. Think of it as de-flaring the case. All you're trying to do is straighten it back out. Neck tension holds the bullet just fine.

Your normal seater die will be able to do this. You might want to do it in two steps, although both seating and crimping can be done at the same time. Just easier to take them one at a time.

Take your barrel out of your gun and drop a finished round in the chamber. Just crimp enough to get it to drop in flush with the barrel hood. It should fall out freely. That's all you need.

No need for the Lee fcd or any other fancy crimp dies. .
Zombie Steve is offline   Reply With Quote
Old 09-13-2012, 12:30   #3
DoctaGlockta
Senior Member
 
DoctaGlockta's Avatar
 
Join Date: Jun 2009
Location: FEMA Region IV
Posts: 2,109
Quote:
Originally Posted by Zombie Steve View Post
Generally, you'll have to taper crimp to get it to function in a semi-auto, but don't think of it as crimping. Think of it as de-flaring the case. All you're trying to do is straighten it back out. Neck tension holds the bullet just fine.

Your normal seater die will be able to do this. You might want to do it in two steps, although both seating and crimping can be done at the same time. Just easier to take them one at a time.

Take your barrel out of your gun and drop a finished round in the chamber. Just crimp enough to get it to drop in flush with the barrel hood. It should fall out freely. That's all you need.

No need for the Lee fcd or any other fancy crimp dies. .
__________________
"Up at Camp David, we do skeet shooting all the time."

- Barack Hussein Obama
DoctaGlockta is offline   Reply With Quote
Old 09-13-2012, 12:35   #4
SPIN2010
Searching ...
 
Join Date: Mar 2010
Location: On the move ... again!
Posts: 1,840
Interesting ... why would you need to crimp straight case based calibers? I would think to just de-flare would be fine. I have never crimped a 9mm, 10mm/.40, or a .45ACP in over thirty years. Curious.

Last edited by SPIN2010; 09-13-2012 at 12:35..
SPIN2010 is offline   Reply With Quote
Old 09-13-2012, 12:42   #5
F106 Fan
Senior Member
 
F106 Fan's Avatar
 
Join Date: Oct 2011
Posts: 5,966
There are some fine target pistols in this world including the Colt Gold Cup and the S&W Model 52 (not even counting all the great .22s such as the S&W Model 41) but the Glock 19 isn't one of them. Nor was it intended to be!

One characteristic of a target pistol is a very crisp trigger break with no perceptible creep. The long-creep trigger of the Glock will never make the cut.

I have to be realistic about my shooting. My eyesight isn't much, my grip is questionable and the trigger on my G21SF just sucks. Still, I can keep the holes in an 8" circle at all practical distances. I can hold the 10 ring at 7 yards so I know the gun will shoot. I am the limiting factor in all my shooting. Not the firearms!

The Lee FCD isn't highly regarded around here for crimping ANY semiauto pistol cases although is sees some use for crimping revolver cases where the bullet has a cannelure such as .38, .44 MAG, .357 MAG and I'm using it to crimp .223 with a 55 gr FMJ. But any roll crimp die would work just as well and they have done so for many decades.

In terms of pistol loading, the FCD is supposed to solve a problem that shouldn't exist (improperly sized cases) and creates a problem that didn't exist (over crimping on straightwall pistol cases).

I prefer a taper crimp die on semiauto cases as a separate operation. Besides testing the loaded round in the chamber (remember, you can fit a bowling ball in a Glock chamber), you should make certain the casemouth of the top round in the magazine doesn't catch on the base of the case being ejected. I place a straightedge along the case to see that the taper has been totally removed.

Pull a few bullets after taper crimping and make sure the casemouth is not being embedded into the bullet. This is particularly important with plated bullets. The plating isn't very thick and cutting through it does nothing for accuracy.

As to measuring the torque applied during crimping, I wonder if the brass wall thickness and annealing make a difference. That is, given a few thousand random cases, all loaded in a batch, it would seem to me that even with consistent torque, some will be crimped more than others.

Of course we have the same problem with any other crimp technique because, unless case length is absolutely uniform, the crimp depth will vary.

For precision rifle, there is an arbor press for bullet seating that measures neck tension. But precision rifle is a whole different thing than loading dumpster quantities of pistol ammo.

Richard
__________________
"No matter how cynical you become, it's never enough to keep up." - Lily Tomlin

Last edited by F106 Fan; 09-13-2012 at 12:44..
F106 Fan is offline   Reply With Quote
Old 09-13-2012, 13:08   #6
fredj338
Senior Member
 
fredj338's Avatar
 
Join Date: Dec 2004
Location: so.cal.
Posts: 21,792
Blog Entries: 3
Quote:
Originally Posted by SPIN2010 View Post
Interesting ... why would you need to crimp straight case based calibers? I would think to just de-flare would be fine. I have never crimped a 9mm, 10mm/.40, or a .45ACP in over thirty years. Curious.
If you are using the taper crimp in the seating die to remove the flare, then you are mildly taper crimping. So yes, always crimp your semiauto ammo ofr proper functioning. Leaving the flare or bell, even only 0.001" can cause feeding issues.
There have been reams written about the uslessness of the LFCD. A poor solution to just about any problem your ammo may have. If you need a LFCD to get your ammo to work, then you need a reloading class not a LFCD.
__________________
"Given adequate penetration, a larger diameter bullet will have an edge in wounding effectiveness. It will damage a blood vessel the smaller projectile barely misses. The larger permanent cavity may lead to faster blood loss. Although such an edge clearly exists, its significance cannot be quantified".

Last edited by fredj338; 09-13-2012 at 13:10..
fredj338 is offline   Reply With Quote
Old 09-13-2012, 13:54   #7
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,353
Taper crimping IS deflaring. Simple as that. Only time your are actually bending the case inward is when you have the bullet seated short enough to bend it inward with out denting the bullet. Its pretty clear if you look at the Lyman reloading manual.
__________________
Steve
Colorado4Wheel is offline   Reply With Quote
Old 09-13-2012, 18:23   #8
fredj338
Senior Member
 
fredj338's Avatar
 
Join Date: Dec 2004
Location: so.cal.
Posts: 21,792
Blog Entries: 3
Quote:
Originally Posted by Colorado4Wheel View Post
Taper crimping IS deflaring. Simple as that. Only time your are actually bending the case inward is when you have the bullet seated short enough to bend it inward with out denting the bullet. Its pretty clear if you look at the Lyman reloading manual.
Yes Steve, but it's not called a taper flare but a taper crimp. Come on guys, you are getting way off into the weeds.
__________________
"Given adequate penetration, a larger diameter bullet will have an edge in wounding effectiveness. It will damage a blood vessel the smaller projectile barely misses. The larger permanent cavity may lead to faster blood loss. Although such an edge clearly exists, its significance cannot be quantified".
fredj338 is offline   Reply With Quote
Old 09-13-2012, 18:46   #9
HAMMERHEAD
Senior Member
 
HAMMERHEAD's Avatar
 
Join Date: Dec 2002
Location: Minnesota
Posts: 4,713
with minimum flare/expansion of the case mouth, all you need to do is bump the case mouth with a taper crimp die to straighten them out. Redding, RCBS, heck, even Lee make good crimp dies.
No need for the FCD or some fancy crimp die.
Sorting cases, ensuring consistent powder charges, straight line bullet seating will all have more affect on accuracy than the brand of crimp die you use.
HAMMERHEAD is offline   Reply With Quote
Old 09-13-2012, 18:53   #10
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,353
Quote:
Originally Posted by fredj338 View Post
Yes Steve, but it's not called a taper flare but a taper crimp. Come on guys, you are getting way off into the weeds.
A roll crimp die would remove the flare just as well. Just saying. It's irrelevant if all you do is use minimal flare and the declare.
__________________
Steve

Last edited by Colorado4Wheel; 09-13-2012 at 18:53..
Colorado4Wheel is offline   Reply With Quote
Old 09-13-2012, 19:14   #11
SPIN2010
Searching ...
 
Join Date: Mar 2010
Location: On the move ... again!
Posts: 1,840
Just an example.

Quote: Throughout the rest of this discussion, bear in mind the fact that not all cartridges will require a crimp of any kind. For those cartridges which can be loaded without resorting to a crimp, we recommend omitting this step altogether.

http://exteriorballistics.com/reloadbasics/crimp.cfm


... and to be fair. The article covers taking out the flare on a straight case as crimping.
SPIN2010 is offline   Reply With Quote
Old 09-13-2012, 20:06   #12
sciolist
Senior Member
 
Join Date: Nov 2009
Location: PNW
Posts: 1,504
I taper crimp all my 9mm to 0.375.
sciolist is offline   Reply With Quote
Old 09-14-2012, 09:55   #13
dhgeyer
Senior Member
 
Join Date: Jul 2011
Posts: 423
Since no one else has mentioned it, I will. Too much crimp can be dangerous. Remember, the 9mm, 40, 45, and other straight walled rimless pistol cases headspace on the case mouth running into the step at the end of the chamber. If a case is crimped too much, it could wedge itself a bit past that step. This would drastically raise pressure, as the case would not release the bullet properly.

This degree of overcrimping would be difficult with standard dies for the caliber. But it is possible if one gets overzealous. When setting up the seating/taper crimping die, look to see if the case mouth is getting deformed or shaved. If it is, that's way too much crimp. And NEVER NEVER roll crimp a straight walled rimless pistol cartridge for a semi-auto pistol. Roll crimping is for revolvers with rimmed cases, or rifle cartridges. This would be hard to do anyway unless one was using bullets with a groove or cannelure. Cast bullets have them. One could overcrimp a soft lead bullet, too, to the point of being dangerous.
dhgeyer is offline   Reply With Quote
Old 09-14-2012, 10:35   #14
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,654
Quote:
Originally Posted by sciolist View Post
I taper crimp all my 9mm to 0.375.
That seems like a lot as the SAAMI case mouth measurement is .380.
SARDG is offline   Reply With Quote
Old 09-14-2012, 13:44   #15
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,654
Quote:
Originally Posted by SARDG View Post
That seems like a lot as the SAAMI case mouth measurement is .380.
I've been measuring factory and some of my reloads with different bullets... Is that SAAMI figure "nominal"? "maximum"? There is no time in the reloading process where .380 is achieved with my setup (except the temporary flare of course).
SARDG is offline   Reply With Quote
Old 09-14-2012, 14:02   #16
F106 Fan
Senior Member
 
F106 Fan's Avatar
 
Join Date: Oct 2011
Posts: 5,966
The .3800" dimension is a 'reference'. There is no tolerance specified other than note about Body Diameter - 0.007".

The .3800" also must be a MAX number because the chamber is spec'd at 0.3810" and there must be some clearance or the slightest puff of smoke will keep a round from chambering.

The .3810" dimension is also a 'reference'. If it has a tolerance, it is +0.004".

Notice that the 0.3800" and 0.3810" are specified to the nearest ten thousandth of an inch. The spec if very serious about these numbers to have spec'd them to 4 decimal places.

Richard
__________________
"No matter how cynical you become, it's never enough to keep up." - Lily Tomlin
F106 Fan is offline   Reply With Quote
Old 09-14-2012, 18:09   #17
fredj338
Senior Member
 
fredj338's Avatar
 
Join Date: Dec 2004
Location: so.cal.
Posts: 21,792
Blog Entries: 3
Quote:
Originally Posted by Colorado4Wheel View Post
A roll crimp die would remove the flare just as well. Just saying. It's irrelevant if all you do is use minimal flare and the declare.
Correct & I have done that. Still, it is correct to call it crimping because you are using a taper crimp die. Semantics maybe, but is what it is. FWIW, I don'tthink I have ecer measured case mouth crimp. If you can see a crimp w/ a taper crimp, it's too much.
__________________
"Given adequate penetration, a larger diameter bullet will have an edge in wounding effectiveness. It will damage a blood vessel the smaller projectile barely misses. The larger permanent cavity may lead to faster blood loss. Although such an edge clearly exists, its significance cannot be quantified".

Last edited by fredj338; 09-14-2012 at 18:11..
fredj338 is offline   Reply With Quote
Old 09-14-2012, 18:16   #18
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,353
I just want people to understand that you don't actually bend the case inward.
__________________
Steve

Last edited by Colorado4Wheel; 09-14-2012 at 18:16..
Colorado4Wheel is offline   Reply With Quote
Old 09-14-2012, 19:21   #19
unclebob
Senior Member
 
unclebob's Avatar
 
Join Date: Oct 2000
Location: Mary Esther FL
Posts: 6,878
Quote:
Originally Posted by F106 Fan View Post
The .3800" dimension is a 'reference'. There is no tolerance specified other than note about Body Diameter - 0.007".

The .3800" also must be a MAX number because the chamber is spec'd at 0.3810" and there must be some clearance or the slightest puff of smoke will keep a round from chambering.

The .3810" dimension is also a 'reference'. If it has a tolerance, it is +0.004".

Notice that the 0.3800" and 0.3810" are specified to the nearest ten thousandth of an inch. The spec if very serious about these numbers to have spec'd them to 4 decimal places.

Richard
And if you over crimp you start sizing the bullet.
__________________
Team Carver Custom
NRA Certified Instructor
NRA Benefactor Life Member
GSSF Life Member
___________________________________________
unclebob is offline   Reply With Quote
Old 09-14-2012, 22:45   #20
fredj338
Senior Member
 
fredj338's Avatar
 
Join Date: Dec 2004
Location: so.cal.
Posts: 21,792
Blog Entries: 3
Quote:
Originally Posted by Colorado4Wheel View Post
I just want people to understand that you don't actually bend the case inward.
Very true, why I always tell noobs to pull a bullet & see how it looks. You can also over crimp w/ a roll crimp, but it's harder to do.
__________________
"Given adequate penetration, a larger diameter bullet will have an edge in wounding effectiveness. It will damage a blood vessel the smaller projectile barely misses. The larger permanent cavity may lead to faster blood loss. Although such an edge clearly exists, its significance cannot be quantified".
fredj338 is offline   Reply With Quote

 
  
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




All times are GMT -6. The time now is 02:44.




Homepage
FAQ
Forums
Calendar
Advertise
Gallery
GT Wiki
GT Blogs
Social Groups
Classifieds


Users Currently Online: 588
131 Members
457 Guests

Most users ever online: 2,672
Aug 11, 2014 at 2:31