Important Notice: The site is currently being upgraded to a new software system. This process could take a day or two to complete. During that time, we are going to leave the site up here, on its old software. WHAT GETS POSTED HERE DURING THIS TRANSITION WILL NOT BE COPIED OVER ONTO THE NEW SITE, WHEN THE UPGRADE IS COMPLETE. When we swap over, the content posted while this message is visible will be lost. We wanted to give you folks a place to hang out and talk while we worked though. We will let you know when we are finished. Please pardon the inconvenience, during this transition.

Home Forums Classifieds GT Store Blogs Today's Posts Search Social Groups


Glock Talk
Welcome To The Glock Talk Forums.

Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 01-16-2013, 23:50   #1
woo woo
Berto's Avatar
Join Date: Sep 2003
Location: WA
Posts: 31,912

CZ 452 trigger adjust (pics)

Since I've had my CZ 452 ZKM 2E in .17hmr, I have really enjoyed it's accuracy. I typically get under an inch for 5 shots at 100yrds...which is very good, but I absolutely know it is more accurate. I can tell I am muscling the gun around too much, fighting a stiff trigger.
I don't have a trigger guage, but I have a good idea this one is over 5-6lbs. It has a little takeup, which is fine, but it's just a stiff trigger. You pull, then pull a little harder, then pull a bit more before it finally breaks. All while maintaining breath control and scope picture. Sometimes I have to stop and start over because it takes too damn long to get the shot off.
So I'm fixing the friggin trigger.

A little research indicated this was a fairly straightforward deal;

The trigger is already adjustable, but general feedback lead me to conclude it wouldn't be enough since the factory spring is nuts-heavy.

I pulled the barreled action from the stock (yes, it's beechwood, not walnut) and went to work....

Rimfire Forum

Pretty simple, trigger, sear mechanism and trigger strut with spring that probably belongs in the valvetrain of a car.
You can see the factory had it set pretty stiff with the adjustment nut actually tightened almost all the way down, too. Backing it all the way off would have dropped about 1/2 to a full pound off the pull....not enough.
Rimfire Forum

I had done a little snooping around my local screw supply store (Tacoma Screw), and found a nice little spring of similar dimensions, but much lighter spring rate. It's a # 154 on their spring chart.

Here, you can see it above the stock spring. Also, the drift pin I removed to free the strut, the washer for the adj nut (which also indexes to prevent the nut from loosening) and a molly bolt insert I use for dry-firing in rimfires.

Rimfire Forum

A kit is available with different springs and shims to eliminate the creep or takeup. I actually like a little takeup, especially with a light trigger that I'm going for, so I didn't mess with shimming the front pivot of the trigger. Just a spring swap.

The trigger is back together now, lighter spring installed.
I inserted the bolt and checked for pull weight, reset and insured the trigger was safe from being jarred or bumped.
No issues.
....and it's NICE, about a third of what it used to be. Maybe 2lbs and crisp.

Rimfire Forum

I will actually loc tite (blue) the adj nut and assembly screws when the action goes back into the stock. The bbl looked fine at the forend too, it's free floated to about 2" ahead of the front action pillar, which should be right. I've heard that they often have too much contact from the factory.

Wish me luck.
The West is the Best.
Berto is offline   Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -6. The time now is 07:03.

GT Wiki
GT Blogs
Social Groups
GT Store

Users Currently Online: 712
192 Members
520 Guests

Most users ever online: 4,867
May 19, 2015 at 1:03